FREE USPS PRIORITY SHIPPING ON ALL DOMESTIC ORDERS OVER $100

DYS F4 Pro Version 2

DYS F4 Pro Version 2

Part Number:4405
review
5
0
5
Your Price: $38.20
In Stock

Description

DYS F4 PRO V2 flight control with high performance which is designed for FPV hobbyists. Not only combine PDB board together with flight control, but also integrated OSD, current meter, voltmeter and built-in high power BEC etc functions.

DYS F4 PRO V2 flight control can meet all the functions you need include FPV racer, aerobatic flight and aerial photograph.

Specification

Betaflight “DYS F4 PRO” firmware

STM32F405 master with higher refresh rate and more function ports

5V 3A BEC output

9V 1.2A BEC output

3.3V 0.3A BEC output

Compatible all split-type escs, connect with DYS 4-in-1 esc (F20A or F30A) with flexible flat cable

Support BF setting software to flash and debug OSD

Integrated current sensor to monitor the power consumption etc in real time

Use remote control to view flight control parameter through OSD

Support SAMRT AUDIO, adjust the VTX by OSD

Comes with heat resistance damping ball to upgrade the stability and operation

3-6s lipo input, integrated PDB, max withstand current 160A

Net weight 10.5g, exclude the cable

The refresh rate of PID and gyro up to 8K

Data

Whole size:L 38mmX W 38mm, hole distance30.5X30.5mm

Six-layer PCB board and 3OZ copper to enhance the over-current and heat dissipation

PDB board with reverse high voltage protection circuit     -MCU:STM32F405 GRT6    -IMU:MPU-6000    -OSD:AT7456E    -FLASH: 8M memory

- Current sensor:0-200A

- Added S5,S6 motor control signal (support 6 axis feature once firmware upgraded)

- Integrated reverse high voltage protection circuit

- Integrated circuit protection to USB port

- 3.3V LDO to power on internal circuit

- 9V BEC: 1.2A

- 5V BEC: 3A/ one-way output to avoid external interference

- When use with 4-in-1 esc, plug in the battery to supply the flight control instead of BEC.

 

2. Connection

V+ V-:For esc power cable

S1-S6:For GND of the corresponding esc signal cable

BOOT:BOOT button  ( for firmware flash)

5V:3A output, can connect with VTX, receiver, lens etc 5V power device at the same time

9V:1.5A output, can connect with wide voltage device, such as 7-24V power VTX etc.3.3V:Power supply for DSMX etc 3.3V power device

GND:Negative

Vout:Video output for VTX image signal cable

Vin:Video input for camera signal cable

LED:Programmable LED signal cable output

RX1:For sbus etc receiver

PPM:For PPM receiver signal pad

USart6 tx:Smart Audio set the VTX function( The VTX should support to use Smart Audio function)

BAT+/BAT-:Battery voltage

 Buzz-Buzz+:Wiring for buzzer 

 

3.Installation with DYS 4-in-1 esc (optional)

Connect DYS F20A or F30A with flexible flat cable, no need to solder

 Note

Please mount the mini F4 with the 4-in-1 esc as pic shows. Be attention that do avoid damage the socket


While using with 4-in-1 esc

Please solder the battery power cable with esc power cable, do not connect with battery


The current meter will be no use when use with 4-in-1 esc


With voltage detection for battery

Caution

Please be attention to below attentions, otherwise your flight control will work improperly or damage.

Please be always attention for the polarity. Double check before power on.

Please keep the power off while plug or pull or any connection.

Do not short the 5V or battery port, otherwise the flight control will be burnt

After finished assemble, please check carefully and clean the residual solder splash to avoid short the components.

Please mount the damping ball on the flight control (Equipped with accessory bag).

If connect with 4-in-1 esc, please ensure the installation connect properly. Please do not force to plug or pull.

Related Items

Customer Reviews

5 Stars
Dys f4 version 2
I bashed my original dys f4 and saw this version released so went for it. I like the layout better without tabs hanging out of the board, and also the 5v 3a regulator seems great so far, I power my unify just fine and clear video. The instruction paper is a bit condescending but if you have done one you can do this one. I'd recommend if your a omnibus fan. Seems a lil more solid compared to the first version. I have not used a AIO esc with it but seems easy.
Did you find this helpful?  1 of 1 Found Helpful
Reviewed by: (Verified Buyer)  from Flagstaff AZ. on 12/4/2017
5
5 Stars
Excellent
I have 3 of these on builds and they have been stellar. Great combo with the ESC stack.
Did you find this helpful?  1 of 1 Found Helpful
Reviewed by: (Verified Buyer)  from Detroit Burbs. on 12/3/2017
5
5 Stars
DYS F4 Pro V2 nice!
Very nice FC. Fit right into my Fusion no fuss wiring and it is holding up nicely as I try not to dip to low back to earth too quickly (read crash learning!) I really like Pyrodrone for my very important items such as FC's and motors, pricing, and extremely fast shipping! Rarely if ever have I found an item "out of stock." I'll be suiting up my xhover R5X soon and Pyrodrone will get the order for another FC and my fourth set of silky smooth motors. It's all about reliability and everything is beautiful!
Did you find this helpful? 
Reviewed by: (Verified Buyer)  from USA. on 11/13/2018
5

Recently Viewed Items

Information
Browse By Category